Skip to main content
Tagasi

EVS-EN ISO 17511:2021

In vitro diagnostikameditsiiniseadmed. Nõuded kaliibrimisvahendite, kontrollmaterjalide ja inimpäritolu näidiste metroloogilise jälgitavuse suhtes

Üldinfo

Kehtiv alates 15.06.2021
Alusdokumendid
ISO 17511:2020; EN ISO 17511:2021

Standardi ajalugu

Staatus
Kuupäev
Tüüp
Nimetus
15.06.2021
Põhitekst
06.10.2003
Põhitekst
This document specifies technical requirements and documentation necessary to establish metrological traceability of values assigned to calibrators, trueness control materials and human samples for quantities measured by IVD MDs. The human samples are those intended to be measured, as specified for each IVD MD. Metrological traceability of values for quantities in human samples extends to the highest available reference system component, ideally to RMPs and certified reference materials (CRMs).
All parties having a role in any of the steps described in a calibration hierarchy for an IVD MD are subject to the requirements described. These parties include but are not limited to manufacturers (of IVD MDs), RMP developers (see ISO 15193), RM producers (see ISO 15194), and reference/calibration laboratories (see ISO 15195) supporting calibration hierarchies for IVD MDs.
NOTE 1 Producers of RMs intended for use in standardization or calibration of IVD MDs include commercial and non-commercial organizations producing RMs for use by many end-users of IVD MDs and/or calibration laboratories, or for use by a single end-user medical laboratory, as in the case of a measurement standard (calibrator) intended to be used exclusively for calibration of a laboratory-developed MP.
This document is applicable to:
a) all IVD MDs that provide measurement results in the form of numeric values, i.e. rational (ratio) and/or differential (interval) scales, and counting scales.
b) IVD MDs where the measurement result is reported as a qualitative value established with a ratio of two measurements (i.e. the signal from a specimen being tested and the signal from a RM with a specified concentration or activity at the cut-off), or a counting scale, with corresponding decision threshold(s). This also includes IVD MDs where results are categorized among ordinal categories based on pre-established quantitative intervals for a quantity.
c) RMs intended for use as trueness control materials for verification or assessment of calibration of IVD MDs, i.e. some commutable CRMs and some external quality assessment (EQA) materials (if so indicated in the RM's intended use statement).
d) IVD MD-specific calibrators and trueness control materials with assigned values, intended to be used together with a specified IVD MD.
e) IVD MDs as described in a) and b), where no end-user performed calibration is required (i.e. when the manufacturer performs a factory calibration of the IVD MD).
This document is not applicable to:
a) calibrators and trueness control materials for IVD MDs which, due to their formulation, are known to have zero amount of measurand;
b) control materials that are used only for internal quality control purposes in medical laboratories to assess the imprecision of an IVD MD, either its repeatability or reproducibility, and/or for assessing changes in IVD MD results compared to a previously established calibration condition;
c) control materials that are used only for internal quality control purposes in medical laboratories and which are supplied with intervals of suggested acceptable values that are not metrologically traceable to higher order reference system components;
d) properties reported as nominal scales and ordinal scales, where no magnitude is involved.
NOTE 2 Nominal scales are typically used to report e.g. identity of blood cell types, microorganism types, identity of nucleic acid sequences, identity of urine particles.

Nõutud väljad on tähistatud *

*
*
*
PDF
31,72 € koos KM-ga
Paber
31,72 € koos KM-ga
Sirvi standardit alates 2,44 € koos KM-ga
Standardi monitooring

Teised on ostnud veel

Põhitekst

EVS-EN ISO 15223-1:2021

Meditsiiniseadmed. Tootjainfos kasutatavad tingmärgid. Osa 1: Üldnõuded
Uusim versioon Kehtiv alates 01.10.2021
Põhitekst

EVS-EN IEC 61326-2-6:2021

Elektrilised mõõtmis-, juhtimis- ja laboratooriumiseadmed. Elektromagnetilise ühilduvuse nõuded. Osa 2-6: Erinõuded. In vitro diagnostilised (IVD) meditsiiniseadmed
Uusim versioon Kehtiv alates 15.06.2021
Põhitekst + muudatus

EVS-EN 62366-1:2015+A1:2020

Meditsiiniseadmed. Osa 1: Kasutatavusprojekteerimise rakendamine meditsiiniseadmetele
Uusim versioon Kehtiv alates 17.08.2020
Põhitekst + muudatus

EVS-EN 62304:2006+A1:2015

Meditsiiniseadmete tarkvara. Tarkvara elutsükli protsessid
Uusim versioon Kehtiv alates 15.11.2019