Skip to main content
Tagasi

EVS-EN ISO 21304-1:2019

Plastics - Ultra-high-molecular-weight polyethylene (PE-UHMW) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 21304-1:2019)

Üldinfo

Kehtiv alates 02.05.2019
Alusdokumendid
ISO 21304-1:2019; EN ISO 21304-1:2019
Tegevusala (ICS grupid)
83.080.20 Termoplastid
Direktiivid või määrused
puuduvad

Standardi ajalugu

Staatus
Kuupäev
Tüüp
Nimetus
02.05.2019
Põhitekst
01.11.2001
Põhitekst
This document establishes a system of designation for thermoplastic PE-UHMW materials, which can be used as the basis for specifications.
For the purposes of this document, PE-UHMW materials are polyethylene materials having a melt mass-flow rate (MFR) of less than 0,1 g/10 min, measured at 190 °C and 21,6 kg load.
NOTE It has been confirmed that the melt volume-flow rate (MVR) is useful for characterizing some PE-UHMW materials (e.g. pipe materials) under the test condition of 230 °C/21,6 kg and bore diameter of die with 3,628 mm (see ISO 21304-2).
The types of PE-UHMW are differentiated from each other by a classification system based on appropriate levels of the designatory properties:
a) viscosity number;
b) elongational stress;
c) Charpy double-notched impact strength;
and on information about the intended application and/or method of processing, important properties, additives, colorants, fillers and reinforcing materials.
This designation system is applicable to all PE-UHMW homopolymers and to ultra-high-molecular-weight copolymers of ethylene having a content of other 1-olefinic monomers of less than 50 % by mass and a content of non-olefinic monomers with functional groups up to a maximum of 3 % by mass. It applies to materials ready for normal use in the form of powder, granules or pellets, unmodified or modified by colorants, fillers and other additives.
It is not intended to imply that materials having the same designation give necessarily the same performance. This document does not provide engineering data, performance data or data on processing conditions which can be required to specify a material. If such additional properties are required, they are intended to be determined in accordance with the test methods specified in ISO 21304-2, if suitable.
In order to specify a thermoplastic PE-UHMW material to meet particular specifications, the requirements are to be given in data block 5 (see 4.1).

Nõutud väljad on tähistatud *

*
*
*
PDF
12,20 € koos KM-ga
Paber
12,20 € koos KM-ga
Sirvi standardit alates 2,44 € koos KM-ga
Standardi monitooring

Teised on ostnud veel

Põhitekst

EVS-EN ISO 19069-1:2015

Plastid. Polüpropüleenist (PP) vormimis- ja ekstrusioonimaterjalid. Osa 1: Tähistussüsteem ja tehniliste andmete alused
Uusim versioon Kehtiv alates 02.04.2015
Põhitekst

EVS-EN ISO 21302-1:2019

Plastics - Polybutene-1 (PB-1) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 21302-1:2019)
Uusim versioon Kehtiv alates 17.06.2019
Põhitekst

EVS-EN ISO 17855-1:2014

Plastics - Polyethylene (PE) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 17855-1:2014)
Uusim versioon Kehtiv alates 09.12.2014
Põhitekst

EVS-EN ISO 20028-1:2019

Plastics - Thermoplastic polyester (TP) moulding and extrusion materials - Part 1: Designation system and basis for specification (ISO 20028-1:2019)
Uusim versioon Kehtiv alates 01.11.2019