Skip to main content
Tagasi

EVS-EN IEC 60512-1:2018

Connectors for electrical and electronic equipment - Tests and measurements - Part 1: Generic specification

Üldinfo

Kehtiv alates 19.12.2018
Alusdokumendid
IEC 60512-1:2018; EN IEC 60512-1:2018
Direktiivid või määrused
puuduvad

Standardi ajalugu

Staatus
Kuupäev
Tüüp
Nimetus
19.12.2018
Põhitekst
01.01.2003
Põhitekst
IEC 60512-1:2018 is intended to be used as a basis for tests and measurements specifications for electrical connectors. It provides guidance and reference for tests and measurements within the IEC 60512 series. It includes the description and the practice of the various phases of tests and measurements (preparation, tests and measurements, requirements, documentation), in addition to basic terms and definitions applicable to any part of the IEC 60512 series. This standard shall be used in conjunction with IEC 60512-1-101 and relevant part(s) of series IEC 60512. Part 60512-1-100 provides the list of the existing test and measuring methods published within series IEC 60512. Detail tests and measurements specifications are applicable to electrical connectors and their components (e.g. connector inserts, connector housings, locking mechanisms, contacts and terminations) within the scope of technical committee 48. They may also be used for similar devices when specified in a detail product specification. Detail tests and measurements specifications are used in conjunction with detail product specifications which prescribe the tests to be used, the required degree of severity for each of them and the permissible performance limits. The detail product specification also specifies the deviations in procedures, which may be required when applying a test to the type of connector or its component under consideration, and it further specifies any special procedures which may be required. This fifth edition cancels and replaces the fourth edition, published in 2001. It constitutes a technical revision. This edition includes the following main technical changes with respect to the previous edition:
– in Clause 3, only terms relating to the testing are defined, and IEC 61076-1 is referred to for terms of connectors.
– Clause 4 (Numbering of tests and measurement specification) is added.
– Subclause 5.1.2 (Calibration) is added.
– in Clause 6 (Test), test procedure follows IEC 60068-1.

Nõutud väljad on tähistatud *

*
*
*
PDF
15,86 € koos KM-ga
Paber
15,86 € koos KM-ga
Sirvi standardit alates 2,44 € koos KM-ga
Standardi monitooring

Teised on ostnud veel

Põhitekst

EVS-EN 60512-1-100:2012

Connectors for electronic equipment - Tests and measurements - Part 1-100: General - Applicable publications
Uusim versioon Kehtiv alates 05.06.2012
Põhitekst

EVS-EN 60512-16-4:2008

Connectors for electronic equipment - Tests and measurements - Part 16-4: Mechanical tests on contacts and terminations - Test 16d: Tensile strength (crimped connections)
Uusim versioon Kehtiv alates 05.09.2008
Põhitekst

EVS-EN 60512-16-7:2008

Connectors for electronic equipment - Tests and measurements - Part 16-7: Mechanical tests on contacts and terminations - Test 16g: Measurement of contact deformation after crimping
Uusim versioon Kehtiv alates 07.11.2008
Põhitekst

EVS-EN 60512-16-8:2008

Connectors for electronic equipment - Tests and measurements -- Part 16-8: Mechanical tests on connections and terminations - Test 16h: Insulating grip effectiveness (crimped connections)
Uusim versioon Kehtiv alates 05.09.2008