Skip to main content
Tagasi

EVS-EN IEC 60238:2018

Edisonkeermega lambipesad

Üldinfo

Kehtiv alates 03.05.2018
Alusdokumendid
EN IEC 60238:2018; IEC 60238:2016
Tegevusala (ICS grupid)
29.140.10 Lambisoklid ja -pesad
Direktiivid või määrused
2014/35/EU Madalpinge

Standardi ajalugu

Staatus
Kuupäev
Tüüp
Nimetus
15.02.2022
Põhitekst + muudatus
01.12.2021
Põhitekst + muudatus
01.12.2021
Muudatus
EVS-EN IEC 60238:2018/A11:2021
15.10.2021
Muudatus
16.08.2018
Muudatus
03.05.2018
Põhitekst
04.05.2011
Muudatus
07.11.2008
Muudatus
07.03.2005
Põhitekst
This International Standard applies to lampholders with Edison thread E14, E27 and E40, designed for connection to the supply of lamps and semi-luminaires1 only.
It also applies to switched-lampholders for use in AC circuits only, where the working voltage
does not exceed 250 V r.m.s.
This standard also applies to lampholders with Edison thread E5 designed for connection to the supply mains of series connected lamps, with a working voltage not exceeding 25 V, to be used indoors, and to lampholders with Edison thread E10 designed for connection to the supply mains of series connected lamps, with a working voltage not exceeding 60 V, to be used indoors or outdoors. It also applies to lampholders E10 for building-in, for the connection of single lamps to the supply. These lampholders are not intended for retail sale.
As far as it reasonably applies, this standard also covers lampholders other than lampholders with Edison thread designed for connection of series-connected lamps to the supply.
NOTE This type of lampholder is for example used in Christmas tree lighting chains.
As far as it reasonably applies, this standard also covers adapters.
This standard also covers lampholders which are, wholly or partly, integral with a luminaire or
intended to be built into appliances. It covers the requirements for the lampholder only. For all other requirements, such as protection against electric shock in the area of the terminals or of the lamp cap, the requirements of the relevant appliance standard are observed and
tested after building into the appropriate equipment, when that equipment is tested according
to its own standard. Such lampholders as well as lampholders provided with a snap-on outer shell, for use by luminaire manufacturers only, are not for retail sale.
This standard applies to lampholders to be used indoors or outdoors in residential as well as in industrial lighting installations. It also applies to candle lampholders. In locations where special conditions prevail, as for street lighting, on board ships, in vehicles and in hazardous locations, for example where explosions are liable to occur, special constructions may be required.
This standard does not apply to three-light lampholders E26d. This standard is based on the following data relative to lamps for general lighting service:
– caps E14 are used for lamps with a current not exceeding 2 A;
– caps E27 are used for lamps with a current not exceeding 4 A;
– caps E40 are used for lamps with a current not exceeding 16 A, or 32 A if the nominal voltage of the supply does not exceed 130 V (see 5.5 and 6.3).
Where lampholders are used in luminaires, their maximum operating temperatures are specified in IEC 60598.

Nõutud väljad on tähistatud *

*
*
*
PDF
39,04 € koos KM-ga
Paber
39,04 € koos KM-ga
Sirvi standardit alates 2,44 € koos KM-ga
Standardi monitooring

Teised on ostnud veel

Muudatus

EVS-EN IEC 60238:2018/A1:2018

Edisonkeermega lambipesad
Kehtiv alates 16.08.2018
Muudatus

EVS-EN 60335-1:2012/A13:2017

Majapidamis- ja muud taolised elektriseadmed. Ohutus. Osa 1: Üldnõuded
Kehtetu alates 29.12.2023
Põhitekst

EVS-EN 60669-2-5:2016

Lülitid majapidamis- ja muudele taolistele kohtkindlatele elektripaigaldistele. Osa 2-5: Erinõuded. Elamute ja muude ehitiste elektroonikasüsteemide lülitid ja nende juurde kuuluvad tarvikud
Kehtetu alates 01.03.2024
Põhitekst

EVS-EN ISO 16089:2015

Tööpingid. Ohutus. Statsionaarsed lihvimismasinad
Uusim versioon Kehtiv alates 05.01.2016