Skip to main content
Tagasi

EVS-EN 14318-1:2013

Ehituslikud soojusisolatsioonitooted. Peenpihustatud jäigad vahtpolüuretaan- (PUR) ja vahtpolüisotsüanuraattooted (PIR). Osa 1: Paigaldamata toodete spetsifikatsioon

Üldinfo

Kehtiv alates 05.02.2013
Alusdokumendid
EN 14318-1:2013
Direktiivid või määrused
305/2011 Ehitustooted

Standardi ajalugu

Staatus
Kuupäev
Tüüp
Nimetus
05.02.2013
Põhitekst
This European Standard specifies requirements for in-situ formed dispensed rigid polyurethane (PUR) and rigid polyisocyanurate (PIR) foam products when installed into cavity walls. This Part 1 of this European Standard is a specification for the rigid foam dispensing system before installation. Part 1 of this European Standard describes the product characteristics and includes procedures for testing, marking and labelling and the rules for evaluation of conformity. This European Standard does not specify the required levels of all properties that should be achieved by a product to demonstrate fitness for purpose in a particular end-use application. The required levels are to be found in regulations or non-conflicting standards. This European Standard does not cover factory made rigid polyurethane (PUR) or polyisocyanurate (PIR) foam insulation products or in-situ products intended to be used for the insulation of building equipment and industrial installations. NOTE Foam products are either called flexible or rigid. The flexible products are used in upholstery and mattresses and are characterised by their ability to deflect, support and recover to their original thickness continually during their in-use phase. Those that are not flexible are termed rigid and do not possess these flexible characteristics. They are mostly used for thermal insulation purposes and vary widely in their compression strength values. Once the cell structure is crushed in a rigid foam, it does not recover its thickness fully. Some of these rigid foams are very low in density with very low compression strengths and are sometimes described “commercially” as “soft foams” or “semi-rigid” foams. This note has been included to clarify that all foams with such descriptions are covered by this standard’s used of the term rigid foam.

Nõutud väljad on tähistatud *

*
*
*
PDF
31,72 € koos KM-ga
Paber
31,72 € koos KM-ga
Sirvi standardit alates 2,44 € koos KM-ga
Standardi monitooring

Teised on ostnud veel

Põhitekst

EVS-EN 14319-1:2013

Hoonete tehnoseadmete ja tööstuspaigaldiste soojusisolatsioonitooted. Peenpihustatud jäigad vahtpolüuretaan- (PUR) ja vahtpolüisotsüanuraattooted (PIR). Osa 1: Paigaldamata toodete spetsifikatsioon
Uusim versioon Kehtiv alates 05.02.2013
Põhitekst

EVS-EN 14320-1:2013

Hoonete tehnoseadmete ja tööstuspaigaldiste soojusisolatsioonitooted. Pihustatud jäigad vahtpolüuretaan- (PUR) ja vahtpolüisotsüanuraattooted (PIR). Osa 1: Paigaldamata toodete spetsifikatsioon
Uusim versioon Kehtiv alates 05.02.2013
Põhitekst

EVS-EN 14315-1:2013

Ehituslikud soojusisolatsioonitooted. Pihustatud jäigad vahtpolüuretaan- (PUR) ja vahtpolüisotsüanuraattooted (PIR). Osa 1: Pihustatud jäikade vahttoodete paigalduseelne spetsifikatsioon
Uusim versioon Kehtiv alates 05.02.2013
Põhitekst

EVS-EN 12101-3:2015

Suitsu ja kuumuse kontrollsüsteemid. Osa 3: Suitsu ja kuumuse eemaldamise sundventilatsiooniseadmete spetsifikatsioon
Uusim versioon Kehtiv alates 06.10.2015