Back

ISO 7919-2:2009

Mechanical vibration -- Evaluation of machine vibration by measurements on rotating shafts -- Part 2: Land-based steam turbines and generators in excess of 50 MW with normal operating speeds of 1 500 r/min, 1 800 r/min, 3 000 r/min and 3 600 r/min

General information

Withdrawn from 27.07.2017
ICS Groups
17.160 Vibrations, shock and vibration measurements 27.040 Gas and steam turbines. Steam engines 29.160.40 Generating sets
Directives or regulations
None

Standard history

Status
Date
Type
Name
27.07.2017
Main
ISO 20816-2:2017
Main
ISO 7919-2:2009
Main
ISO 7919-2:2001
ISO 7919-2:2009 establishes provisions for applying evaluation criteria for the severity of in-situ, broad-band shaft vibration measured radial (i.e. transverse) to the shaft axis at, or close to, the main bearings. These are in terms of:
- vibration under normal steady-state operating conditions;
- vibration during other (non-steady-state) conditions when transient changes are taking place, including run up or run down, initial loading and load changes;
- changes in vibration which can occur during normal steady-state operation.
ISO 7919-2:2009 is applicable to land-based steam turbines and generators with power outputs greater than 50 MW and a normal operating speed of 1 500 r/min, 1800 r/min, 3 000 r/min or 3 600 r/min.

Required fields are indicated with *

*
*
*
PDF
82.61 € incl tax
Paper
82.61 € incl tax
Standard monitoring
English (PDF 162 KB)

Related products

Main

ISO 20816-2:2017

Mechanical vibration -- Measurement and evaluation of machine vibration -- Part 2: Land-based gas turbines, steam turbines and generators in excess of 40 MW, with fluid-film bearings and rated speeds of 1 500 r/min, 1 800 r/min, 3 000 r/min and 3 600 r/min
Newest version Valid from 27.07.2017
Main

EVS-EN ISO 8528-13:2016

Reciprocating internal combustion engine driven alternating current generating sets - Part 13: Safety (ISO 8528-13:2016, Corrected version 2016-10-15)
Newest version Valid from 05.07.2016
Main

EVS-EN 12952-6:2011

Water-tube boilers and auxiliary installations - Part 6: Inspection during construction; documentation and marking of pressure parts of the boiler
Withdrawn from 31.12.2021
Main

EVS-EN 12952-3:2011

Water-tube boilers and auxiliary installations - Part 3: Design and calculation for pressure parts of the boiler
Withdrawn from 15.11.2022

Customers who bought this item also bought

Main

ISO 10816-2:2009

Mechanical vibration -- Evaluation of machine vibration by measurements on non-rotating parts -- Part 2: Land-based steam turbines and generators in excess of 50 MW with normal operating speeds of 1 500 r/min, 1 800 r/min, 3 000 r/min and 3 600 r/min
Withdrawn from 27.07.2017
Amendment

ISO 10816-1:1995/Amd 1:2009

ISO 10816-1:1995 - Amendment
Withdrawn from 09.11.2016
Main

EVS-EN ISO 11124-3:1999

Preparation of steel substrates before application of paints and related products - Specifications for metallic blast-cleaning abrasives - Part 3: High-carbon cast-steel shot and grit
Withdrawn from 02.11.2018
Main

EVS-EN ISO 11124-4:1999

Preparation of steel substrates before application of paints and related products - Specifications for metallic blast-cleaning abrasives - Part 4: Low-carbon cast-steel shot
Withdrawn from 16.10.2018

Standards designation

EVS Estonian standard
EN European standard (published by an CEN or CENELEC)
EN ISO International standard adopted as an European standard
ISO International Organization for Standardization’s standard
IEC International Electrotechnical Commission’s standard
HD CENELEC’s harmonisation document
   
EVS-EN European standard implemented in Estonia
EVS-EN ISO International standard adopted in Europe and implemented in Estonia
EVS-EN ISO/IEC International standard/International electrotechnical standard adopted in Europe and implemented in Estonia
EVS-IEC International electrotechnical standard implemented in Estonia
EVS-ISO International standard implemented in Estonia
   
A, AMD amedment
+A a full standard plus the amendment
/A only amendment
COR, AC corrigendum
+COR a full standard plus the corrigendum
NA national annex
+NA a full standard plus the national annex
/NA only national annex
TS technical specification
TR technical report
CWA agreement, developed by a CEN or CENELEC
prEVS-EN (etc) draft standard
   
et the standard is in Estonian only
en the standard is in English only
et-en the standard is in Parallel text Estonian-English