Back

EVS-EN ISO 75-3:2004

Plastics - Determination of temperature of deflection under load - Part 3: High-strength thermosetting laminates

General information

Valid from 09.09.2004
Base Documents
ISO 75-3:2004; EN ISO 75-3:2004 + AC:2006
ICS Groups
83.120 Reinforced plastics 83.140.20 Laminated sheets
Directives or regulations
None

Standard history

Status
Date
Type
Name
Main
prEN ISO 75-3
09.09.2004
Main
EVS-EN ISO 75-3:2004
Main
EVS-EN ISO 75-3:2000
This part of ISO 75 specifies a method for the determination of the temperature of deflection under load of highstrength thermosetting laminates and compression-moulded long-fibre-reinforced plastics in which the fibre length is greater than 7,5 mm. The flexural stress used is not fixed, as in ISO 75-2, but is a fraction (1/1 000) of the initial (room-temperature) flexural modulus of the material under test. This allows the method to be applied to materials with a wide range of flexural moduli.

Required fields are indicated with *

*
*
*
PDF
8.54 € incl tax
Paper
8.54 € incl tax
Browse standard from 2.44 € incl tax
Standard monitoring
English (PDF 187 KB)

Related products

Main + amendment

EVS-EN 438-2:2016+A1:2018

High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (usually called laminates) - Part 2: Determination of properties
Newest version Valid from 03.01.2019
Main

EVS-EN 438-1:2016

High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (Usually called Laminates) - Part 1: Introduction and general information
Newest version Valid from 02.03.2016
Main

EVS-EN 438-3:2016

High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (Usually called Laminates) - Part 3: Classification and specifications for laminates less than 2 mm thick intended for bonding to supporting substrates
Newest version Valid from 02.03.2016
Main

EVS-EN ISO 14125:2000

Fibre-reinforced plastic composites - Determination of flexural properties
Newest version Valid from 01.01.2000

Customers who bought this item also bought

Main

EVS-EN ISO 75-1:2020

Plastics - Determination of temperature of deflection under load - Part 1: General test method (ISO 75-1:2020)
Newest version Valid from 02.04.2020
Main

EVS-EN ISO 179-2:2020

Plastics - Determination of Charpy impact properties - Part 2: Instrumented impact test (ISO 179-2:2020)
Newest version Valid from 15.06.2020
Main

EVS-EN ISO 3451-4:2001

Plastics - Determination of ash - Part 4: Polyamides
Withdrawn from 01.04.2024
Main

EVS-EN ISO 75-2:2013

Plastics - Determination of temperature of deflection under load - Part 2: Plastics and ebonite (ISO 75-2:2013)
Newest version Valid from 04.06.2013

Standards designation

EVS Estonian standard
EN European standard (published by an CEN or CENELEC)
EN ISO International standard adopted as an European standard
ISO International Organization for Standardization’s standard
IEC International Electrotechnical Commission’s standard
HD CENELEC’s harmonisation document
   
EVS-EN European standard implemented in Estonia
EVS-EN ISO International standard adopted in Europe and implemented in Estonia
EVS-EN ISO/IEC International standard/International electrotechnical standard adopted in Europe and implemented in Estonia
EVS-IEC International electrotechnical standard implemented in Estonia
EVS-ISO International standard implemented in Estonia
   
A, AMD amedment
+A a full standard plus the amendment
/A only amendment
COR, AC corrigendum
+COR a full standard plus the corrigendum
NA national annex
+NA a full standard plus the national annex
/NA only national annex
TS technical specification
TR technical report
CWA agreement, developed by a CEN or CENELEC
prEVS-EN (etc) draft standard
   
et the standard is in Estonian only
en the standard is in English only
et-en the standard is in Parallel text Estonian-English