Back

EVS-EN ISO 294-3:2003

Plastics - Injection moulding of test specimens of thermoplastic materials - Part 3: Small plates

General information

Withdrawn from 03.08.2020
Base Documents
ISO 294-3; EN ISO 294-3:2003
ICS Groups
83.080.20 Thermoplastic materials
Directives or regulations
None

Standard history

Status
Date
Type
Name
03.08.2020
Main
EVS-EN ISO 294-3:2020
15.12.2003
Main
EVS-EN ISO 294-3:2003
Main
EVS-EN ISO 294-3:2000
This part of ISO 294 specifies two two-cavity moulds, the type D1 and D2 ISO moulds, for the injection moulding of small plates measuring 60 mm × 60 mm with a preferred thickness of 1 mm (type D1) or 2 mm (type D2), which can be used for a variety of tests. The moulds may additionally be fitted with inserts for studying the effects of weld lines on the mechanical properties.

Required fields are indicated with *

*
*
*
PDF
12.20 € incl tax
Paper
12.20 € incl tax
Browse standard from 2.44 € incl tax
Standard monitoring
English (PDF 164 KB)

Related products

Main

EVS-EN ISO 294-3:2020

Plastics - Injection moulding of test specimens of thermoplastic materials - Part 3: Small plates (ISO 294-3:2020)
Newest version Valid from 03.08.2020
Main

EVS-EN 15343:2007

Plastics - Recycled Plastics - Plastics recycling traceability and assessment of conformity and recycled content
Newest version Valid from 08.01.2008
Main

EVS-EN ISO 1133-1:2022

Plastics - Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics - Part 1: Standard method (ISO 1133-1:2022)
Newest version Valid from 15.07.2022
Main

EVS-EN ISO 1133-1:2011

Plastics - Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics - Part 1: Standard method (ISO 1133-1:2011)
Withdrawn from 15.07.2022

Customers who bought this item also bought

Main

EVS-EN ISO 294-4:2003

Plastics - Injection moulding of test specimens of thermoplastic materials - Part 4: Determination of moulding shrinkage
Withdrawn from 15.02.2019
Main

EVS-EN ISO 294-5:2013

Plastics - Injection moulding of test specimens of thermoplastic materials - Part 5: Preparation of standard specimens for investigating anisotropy (ISO 294-5:2011)
Withdrawn from 02.01.2018
Amendment

EVS-EN ISO 294-2:2000/A1:2005

Plastics - Injection moulding of test specimens of thermoplastic materials - Part 2: Small tensile bars
Withdrawn from 03.01.2019
Amendment

EVS-EN ISO 294-1:2000/A1:2002

Plastics - Injection moulding of test specimens of thermoplastic materials - Part 1: General principles, and moulding of multipurpose and bar test specimens
Withdrawn from 16.06.2017

Standards designation

EVS Estonian standard
EN European standard (published by an CEN or CENELEC)
EN ISO International standard adopted as an European standard
ISO International Organization for Standardization’s standard
IEC International Electrotechnical Commission’s standard
HD CENELEC’s harmonisation document
   
EVS-EN European standard implemented in Estonia
EVS-EN ISO International standard adopted in Europe and implemented in Estonia
EVS-EN ISO/IEC International standard/International electrotechnical standard adopted in Europe and implemented in Estonia
EVS-IEC International electrotechnical standard implemented in Estonia
EVS-ISO International standard implemented in Estonia
   
A, AMD amedment
+A a full standard plus the amendment
/A only amendment
COR, AC corrigendum
+COR a full standard plus the corrigendum
NA national annex
+NA a full standard plus the national annex
/NA only national annex
TS technical specification
TR technical report
CWA agreement, developed by a CEN or CENELEC
prEVS-EN (etc) draft standard
   
et the standard is in Estonian only
en the standard is in English only
et-en the standard is in Parallel text Estonian-English