Skip to main content
Back

EVS-EN ISO 180:2019

Plastics - Determination of Izod impact strength (ISO 180:2019)

General information

Withdrawn from 03.07.2023
Base Documents
ISO 180:2019; EN ISO 180:2019
Directives or regulations
None

Standard history

Status
Date
Type
Name
03.07.2023
Main
02.01.2020
Main
06.05.2013
Amendment
EVS-EN ISO 180:2001/A2:2013
06.02.2007
Amendment
EVS-EN ISO 180:2001/A1:2007
01.06.2001
Main
EVS-EN ISO 180:2001
1.1 This document specifies a method for determining the Izod impact strength of plastics under defined conditions. A number of different types of specimen and test configurations are defined. Different test parameters are specified according to the type of material, the type of test specimen and the type of notch.
1.2 The method is used to investigate the behaviour of specified types of specimen under the impact conditions defined and for estimating the brittleness or toughness of specimens within the limitations inherent in the test conditions.
1.3 The method is suitable for use with the following range of materials:
— rigid thermoplastic moulding and extrusion materials, including filled and reinforced compounds in addition to unfilled types; rigid thermoplastics sheets;
— rigid thermosetting moulding materials, including filled and reinforced compounds; rigid thermosetting sheets, including laminates;
— fibre-reinforced thermosetting and thermoplastic composites incorporating unidirectional or non-unidirectional reinforcements such as mat, woven fabrics, woven rovings, chopped strands, combination and hybrid reinforcements, rovings and milled fibres and sheet made from pre-impregnated materials (prepregs);
— thermotropic liquid-crystal polymers.
1.4 The method is not normally suitable for use with rigid cellular materials and sandwich structures containing cellular material. Notched specimens are also not normally used for long-fibre-reinforced composites or thermotropic liquid-crystal polymers.
1.5 The method is suited to the use of specimens which can be either moulded to the chosen dimensions, machined from the central portion of a standard multipurpose test specimen (see ISO 20753) or machined from finished or semi-finished products such as mouldings, laminates and extruded or cast sheet.
1.6 The method specifies preferred dimensions for the test specimen. Tests which are carried out on specimens of different dimensions or with different notches, or specimens which are prepared under different conditions, may produce results which are not comparable. Other factors, such as the energy capacity of the apparatus, its impact velocity and the conditioning of the specimens can also influence the results. Consequently, when comparative data are required, these factors are to be carefully controlled and recorded.
1.7 The method is not intended to be used as a source of data for design calculations. Information on the typical behaviour of a material can be obtained, however, by testing at different temperatures, by varying the notch radius and/or the thickness and by testing specimens prepared under different conditions.

Required fields are indicated with *

*
*
*
PDF
15.86 € incl tax
Paper
15.86 € incl tax
Browse standard from 2.44 € incl tax
Standard monitoring

Customers who bought this item also bought

Main

EVS-EN ISO 179-1:2010

Plastics - Determination of Charpy impact properties - Part 1: Non-instrumented impact test
Withdrawn from 03.07.2023
Main

EVS-EN ISO 1183-1:2019

Plastics - Methods for determining the density of non-cellular plastics - Part 1: Immersion method, liquid pycnometer method and titration method (ISO 1183-1:2019, Corrected version 2019-05)
Newest version Valid from 15.04.2019
Main

EVS-EN ISO 179-2:2020

Plastics - Determination of Charpy impact properties - Part 2: Instrumented impact test (ISO 179-2:2020)
Newest version Valid from 15.06.2020
Main

EVS-EN ISO 527-1:2019

Plastics - Determination of tensile properties - Part 1: General principles (ISO 527-1:2019)
Newest version Valid from 01.10.2019