Back

EVS-EN ISO 10350-1:2017

Plastics - Acquisition and presentation of comparable single-point data - Part 1: Moulding materials (ISO 10350-1:2017)

General information

Valid from 18.12.2017
Base Documents
ISO 10350-1:2017; EN ISO 10350-1:2017
ICS Groups
83.080.20 Thermoplastic materials
Directives or regulations
None

Standard history

Status
Date
Type
Name
Main
prEN ISO 10350-1
18.12.2017
Main
EVS-EN ISO 10350-1:2017
04.08.2014
Amendment
EVS-EN ISO 10350-1:2008/A1:2014
07.10.2008
Main
EVS-EN ISO 10350-1:2008
The ISO 10350 series identifies specific test procedures for the acquisition and presentation of comparable data for certain basic properties of plastics. In general, each property is specified by a single experimental value, although in certain cases properties are represented by two values obtained under different test conditions. The properties included are those presented conventionally in manufacturers' data sheets. ISO 10350-1 applies predominantly to unreinforced and reinforced thermoplastic and thermosetting materials that may be injection- or compression-moulded or prepared as sheets of specified thickness. For the purposes of ISO 10350-1, long-fibre-reinforced plastics are considered to have fibre lengths greater than 7,5 mm prior to moulding.
NOTE ISO 10350-2 deals specifically with long- or continuous-fibre-reinforced plastics.

Required fields are indicated with *

*
*
*
PDF
15.86 € incl tax
Paper
15.86 € incl tax
Browse standard from 2.44 € incl tax
Standard monitoring
English (PDF 551 KB)

Related products

Main

EVS-EN 15343:2007

Plastics - Recycled Plastics - Plastics recycling traceability and assessment of conformity and recycled content
Newest version Valid from 08.01.2008
Main

EVS-EN ISO 1133-1:2022

Plastics - Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics - Part 1: Standard method (ISO 1133-1:2022)
Newest version Valid from 15.07.2022
Main

EVS-EN ISO 1133-1:2011

Plastics - Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics - Part 1: Standard method (ISO 1133-1:2011)
Withdrawn from 15.07.2022
Main

EVS-EN 15345:2008

Plastics - Recycled Plastics - Characterisation of Polypropylene (PP) recyclates
Newest version Valid from 07.02.2008

Customers who bought this item also bought

Main

EVS-EN ISO 527-2:2012

Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics (ISO 527-2:2012)
Newest version Valid from 04.04.2012
Main

EVS-EN ISO 527-1:2019

Plastics - Determination of tensile properties - Part 1: General principles (ISO 527-1:2019)
Newest version Valid from 01.10.2019
Main

EVS-EN ISO 294-4:2019

Plastics - Injection moulding of test specimens of thermoplastic materials - Part 4: Determination of moulding shrinkage (ISO 294-4:2018)
Newest version Valid from 15.02.2019
Main

EVS-EN ISO 294-2:2018

Plastics - Injection moulding of test specimens of thermoplastic materials - Part 2: Small tensile bars (ISO 294-2:2018)
Newest version Valid from 03.01.2019

Standards designation

EVS Estonian standard
EN European standard (published by an CEN or CENELEC)
EN ISO International standard adopted as an European standard
ISO International Organization for Standardization’s standard
IEC International Electrotechnical Commission’s standard
HD CENELEC’s harmonisation document
   
EVS-EN European standard implemented in Estonia
EVS-EN ISO International standard adopted in Europe and implemented in Estonia
EVS-EN ISO/IEC International standard/International electrotechnical standard adopted in Europe and implemented in Estonia
EVS-IEC International electrotechnical standard implemented in Estonia
EVS-ISO International standard implemented in Estonia
   
A, AMD amedment
+A a full standard plus the amendment
/A only amendment
COR, AC corrigendum
+COR a full standard plus the corrigendum
NA national annex
+NA a full standard plus the national annex
/NA only national annex
TS technical specification
TR technical report
CWA agreement, developed by a CEN or CENELEC
prEVS-EN (etc) draft standard
   
et the standard is in Estonian only
en the standard is in English only
et-en the standard is in Parallel text Estonian-English